Menu

ASME BPE 2007 PDF

0 Comments

ASME BPE (Revision of ASME BPE). Bioprocessing. Equipment. AN AMERICAN NATIONAL STANDARD. Three Park Avenue. Buy ASME BPE Bioprocessing Equipment from SAI Global. No reproduction may be made of this material without written consent of ASME. ASME BPE (Revision of ASME BPE) Bioprocessing.

Author: Melmaran Tuktilar
Country: French Guiana
Language: English (Spanish)
Genre: Literature
Published (Last): 5 March 2004
Pages: 385
PDF File Size: 5.57 Mb
ePub File Size: 7.84 Mb
ISBN: 973-1-58122-503-3
Downloads: 97965
Price: Free* [*Free Regsitration Required]
Uploader: Kataur

Obertanec, LJ Star, Inc. GTAW may be performed by adding filler material to the weld, or by a fusion process in which no filler is added. Water used for the following rinse shall meet the requirements of SD Page 2, 3 11 15, 17, 19, 20 Location GR-9 Fig. The equipment is cleaned but not necessarily sterilized.

Nemenoff, Habonim Industrial Valves Ltd.

Open Cross-Sectional Lip Seal. The bore of weld neck flanges shall be the same as the I. It will be the responsibility of the system manufacturer or designer to identify where exceptions exist or where the target ratio of 2: The advance of the welding is manually controlled.

In temporary runs, hose assemblies may be manually drained after disconnecting. The construction of the fitting shall be such that excessive npe of the seal will not be caused as a result of overtightening the nut. Transfer Panel and Jumper Tolerances. Minor, Paul Mueller Co. Gas Lubricated Noncontacting Double Seal.

ASME BPE Guidelines for Pharmaceutical Equipment

Gayer, Paul Mueller Co. Hutton, Chair, Arkema, Inc. Preferred hygienic support design shall incorporate rounded geometry to facilitate draining and cleanability, with minimal potential for the collecting and retaining of dust and residual cleaning solution or spillage on the hanger. Dvorscek, Abbott Laboratories M. Steam trap bodies shall have an internal b;e finish excluding the bellows assembly as agreed to by all parties.

  12N60C DATASHEET PDF

A consumable insert can also be used for the root pass in a multiple pass amse with the addition of filler wire also called insert ring. The number of isolation valves should be minimized. The depth of the drain pan is determined by calculating the largest spill volume and accommodating it with a sufficient pan holding volume.

Drago, Garlock Sealing Technologies R. Wells, Spirax Sarco K. Zinkowski, Vice Chair P. A sanitary weld must be completely penetrated on ame weld ID, with little or no discoloration due to oxidation, and be otherwise without defects that would interfere with maintenance in a clean and sterile condition.

All gasketed fittings should be constructed in such a manner as to avoid dead legs and crevices. Transfer Panel Looped Headers. The results give information about fluid coverage, a requirement for cleanability.

Actually, the blowhole is stretched out in the direction of rolling. Maximum gap allowed at seal point per size Maximum gap allowed at seal point per size Maximum gap allowed at seal point per size Tolerances applied to related nozzles defined by jumper paths 51 Copyright c by the 2007 Society of Mechanical Engineers.

ASME BPE – Wikipedia

If removable, then a positioning device asmme mark shall be incorporated into the design to allow for proper location and cleaning of the equipment. Rau, Dockweiler AG P. Banes, Oakley Specialized Services, Inc. The integrated system makes it possible to achieve complete and uniform control bpf time, temperature, and chemical concentration, all of which are important to success with any mechanical spray or pressure recirculation CIP process.

  EPISTEMOLOGIA NATURALIZADA QUINE PDF

The size of surface deficits is classified in two groups: Davis, GE Healthcare D. MacDonald, United Association D.

Operating conditions include heat-up, hold, and cooldown. To ensure the highest degree of hygienic design, Copyright c by the American Society of Mechanical Engineers.

Brockmann, Alfa Laval, Inc. Supporting skid frame structures and modules should be constructed from fully sealed tubes or pipes, which are easily cleaned. Benway, Be, Swagelok Co. Engineering judgments must be consistent with the fundamental principles of this Standard.

ASME BPE Bioprocessing Equipment_图文_百度文库

A common drain port on the skid is preferred. The rules provide for the adoption of other ASME and related national standards, and when so referenced become part of the standard. For the header and valve size combinations 15 where the target value cannot be met using these configurations, a specific isolation valve design, as shown in Fig.